欢迎来到三八资源网-打印机维修教程 复印机维修手册 打印机清零软件!


柯美

柯尼卡美能达bizhub_225i_215i_205i维修手册

本商品由官方自营店提供
价格:¥30VIP¥27SVIP¥3

购买数量: (库存:充足)

本商品可参与分享赚佣金计划 【佣金3元】 点击参与
目录
修订列表 ...................................................................................................................................... -i
A 安全和重要警告事项 ...........................................................................................................A-1
1. 重要注意事项 .....................................................................................................................................................................................A-2
2. 危险、警告和注意事项说明................................................................................................................................................................A-3
2.1 本维修手册中的事项说明 .........................................................................................................................................................A-3
2.2 安全和重要警告事项说明 .........................................................................................................................................................A-3
3. 安全警告.............................................................................................................................................................................................A-4
3.1 未经柯尼卡美能达办公系统 (中国)有限公司授权的改造......................................................................................................A-4
3.1.1 需要特别注意的行为...................................................................................................................................................................A-4
3.2 电源连接头的选择....................................................................................................................................................................A-5
3.2.1 电源线组件或电源连接头...........................................................................................................................................................A-5
3.3 进行现场维修时的检查要点......................................................................................................................................................A-6
3.3.1 电源...............................................................................................................................................................................................A-6
3.3.2 安装要求.......................................................................................................................................................................................A-8
3.3.3 维修保养后...................................................................................................................................................................................A-9
3.4 保险丝....................................................................................................................................................................................A-12
3.5 废旧电池注意事项..................................................................................................................................................................A-12
3.5.1 所有地区.....................................................................................................................................................................................A-12
3.5.2 德国.............................................................................................................................................................................................A-12
3.5.3 法国.............................................................................................................................................................................................A-12
3.5.4 丹麦.............................................................................................................................................................................................A-12
3.5.5 芬兰,瑞典.................................................................................................................................................................................A-12
3.5.6 挪威.............................................................................................................................................................................................A-12
3.6 激光安全 ................................................................................................................................................................................A-13
3.6.1 激光安全.....................................................................................................................................................................................A-13
3.6.2 内部激光辐射.............................................................................................................................................................................A-13
3.6.3 激光安全标签.............................................................................................................................................................................A-14
3.6.4 激光警告标签.............................................................................................................................................................................A-14
3.6.5 激光设备操作注意事项.............................................................................................................................................................A-15
4. 机器上的警告标识 ............................................................................................................................................................................A-16
4.1 机器内的警告标识..................................................................................................................................................................A-16
4.2 板上的警告标识......................................................................................................................................................................A-17
5. 发生事故时的措施 ............................................................................................................................................................................A-18
B 目录中使用的符号 ..............................................................................................................B-1
1. 本手册使用注意事项...........................................................................................................................................................................B-1
2. 产品名 ................................................................................................................................................................................................B-2
3. 品牌名 ................................................................................................................................................................................................B-3
4. 进纸方向.............................................................................................................................................................................................B-4
5. 有关规格的注意事项...........................................................................................................................................................................B-5
C 产品概述 ............................................................................................................................ C-1
1. 产品规格要求 .................................................................................................................................................................................... C-1
1.1 bizhub 225i/215i/205i.............................................................................................................................................................. C-1
1.1.1 基本规格....................................................................................................................................................................................... C-1
1.1.2 纸张............................................................................................................................................................................................... C-2
1.1.3 打印量........................................................................................................................................................................................... C-2
1.1.4 机器规格....................................................................................................................................................................................... C-2
1.1.5 打印功能....................................................................................................................................................................................... C-3
1.1.6 扫描功能....................................................................................................................................................................................... C-4
1.2 DF-633.................................................................................................................................................................................... C-5
1.3 PF-507.................................................................................................................................................................................... C-8
ii
1.4 AD-509.................................................................................................................................................................................... C-9
1.5 FK-510.................................................................................................................................................................................. C-10
2. 总体构成.......................................................................................................................................................................................... C-11
2.1 系统配置 ............................................................................................................................................................................... C-11
2.2 横断面视图............................................................................................................................................................................ C-12
2.3 纸张通道 ............................................................................................................................................................................... C-13
2.4 控制块状图............................................................................................................................................................................ C-14
2.5 图像生成处理 ........................................................................................................................................................................ C-15
D 维修工具 ............................................................................................................................ D-1
1. bizhub 225i/215i/205i........................................................................................................................................................................ D-1
E 维修保养 .............................................................................................................................E-1
1. 维修保养的概念..................................................................................................................................................................................E-1
2. 定期更换零件列表 ..............................................................................................................................................................................E-2
2.1 bizhub 225i/215i/205i...............................................................................................................................................................E-2
2.2 自动双面输稿器 (DF-633)....................................................................................................................................................E-2
2.3 PF-507.....................................................................................................................................................................................E-2
3. 定期更换步骤 .....................................................................................................................................................................................E-3
3.1 bizhub 225i/215i/205i...............................................................................................................................................................E-3
3.1.1 更换显影剂................................................................................................................................................................................... E-3
3.1.2 更换感光鼓................................................................................................................................................................................... E-5
3.1.3 更换清洁刮板............................................................................................................................................................................... E-6
3.1.4 更换感光鼓充电电晕组件........................................................................................................................................................... E-6
3.1.5 涂抹碳粉....................................................................................................................................................................................... E-7
3.1.6 更换碳粉瓶................................................................................................................................................................................... E-8
3.1.7 更换成像单元............................................................................................................................................................................... E-9
3.1.8 更换转印辊单元......................................................................................................................................................................... E-10
3.1.9 更换定影单元............................................................................................................................................................................. E-10
3.1.10 更换纸盒 1 进纸辊..................................................................................................................................................................... E-11
3.1.11 更换纸盒 1 分离垫..................................................................................................................................................................... E-12
3.1.12 更换手送纸盒进纸辊................................................................................................................................................................. E-13
3.1.13 更换手送纸盒分离辊................................................................................................................................................................. E-14
3.2 自动双面输稿器 (DF-633)..................................................................................................................................................E-15
3.2.1 更换拾纸辊/进纸辊................................................................................................................................................................. E-15
3.2.2 更换分离辊组件......................................................................................................................................................................... E-16
3.3 PF-507...................................................................................................................................................................................E-17
3.3.1 更换进纸辊................................................................................................................................................................................. E-17
4. 清洁零件列表 ...................................................................................................................................................................................E-18
4.1 bizhub 225i/215i/205i.............................................................................................................................................................E-18
4.2 自动双面输稿器 (DF-633)..................................................................................................................................................E-18
4.3 PF-507...................................................................................................................................................................................E-18
5. 清洁 / 润滑步骤.................................................................................................................................................................................E-19
5.1 bizhub 225i/215i/205i.............................................................................................................................................................E-19
5.1.1 清洁 Ds 套环.............................................................................................................................................................................. E-19
5.1.2 清洁感光鼓分离针..................................................................................................................................................................... E-20
5.1.3 清洁显影剂飞散挡板................................................................................................................................................................. E-20
5.1.4 清洁对位辊................................................................................................................................................................................. E-21
5.1.5 清洁预图像转印导板................................................................................................................................................................. E-21
5.1.6 清洁纸盒 1 进纸辊..................................................................................................................................................................... E-22
5.1.7 清洁纸盒 1 分离辊..................................................................................................................................................................... E-23
5.1.8 清洁稿台..................................................................................................................................................................................... E-23
5.1.9 清洁手送纸盒分离辊................................................................................................................................................................. E-23
5.1.10 清洁手送纸盒进纸辊................................................................................................................................................................. E-23
5.2 自动双面输稿器 (DF-633)..................................................................................................................................................E-24
iii
5.2.1 清洁拾纸辊 / 进纸辊 ................................................................................................................................................................. E-24
5.2.2 清洁分离辊................................................................................................................................................................................. E-24
5.2.3 清洁其他辊................................................................................................................................................................................. E-25
5.2.4 清洁其他轮................................................................................................................................................................................. E-26
5.2.5 清洁扫描导板............................................................................................................................................................................. E-26
5.2.6 清洁反射传感器部分................................................................................................................................................................. E-27
5.3 PF-507...................................................................................................................................................................................E-28
5.3.1 清洁进纸辊................................................................................................................................................................................. E-28
5.3.2 清洁垂直传送辊 / 轮 ................................................................................................................................................................. E-28
5.3.3 清洁摩擦片................................................................................................................................................................................. E-28
5.4 AD-509...................................................................................................................................................................................E-29
5.4.1 清洁自动双面器单元传送辊 / 轮 ............................................................................................................................................. E-29
5.4.2 清洁反转部分传送辊 / 轮 ......................................................................................................................................................... E-29
5.4.3 清洁自动双面器单元通风部分................................................................................................................................................. E-29
F 拆卸 / 重新组装 ...................................................................................................................F-1
1. 拆卸 / 调整禁用项目 ...........................................................................................................................................................................F-1
1.1 涂漆螺钉 ..................................................................................................................................................................................F-1
1.2 漆成红色的螺钉........................................................................................................................................................................F-1
1.3 电路板上的可变电阻器.............................................................................................................................................................F-1
1.4 关于拆卸的警告........................................................................................................................................................................F-1
1.5 安装或运输期间的警告 / 注意事项............................................................................................................................................F-1
2. 禁止拆卸的单元..................................................................................................................................................................................F-3
2.1 PH 单元....................................................................................................................................................................................F-3
2.1.1 禁止的原因................................................................................................................................................................................... F-3
2.2 定影单元 ..................................................................................................................................................................................F-3
2.2.1 禁止的原因................................................................................................................................................................................... F-3
3. 拆卸/组装警告 / 注意事项.................................................................................................................................................................F-4
3.1 卸下 / 安装 PWB ......................................................................................................................................................................F-4
4. bizhub 225i/215i/205i.........................................................................................................................................................................F-5
4.1 外部零件 ..................................................................................................................................................................................F-5
4.1.1 前门............................................................................................................................................................................................... F-5
4.1.2 前盖............................................................................................................................................................................................... F-5
4.1.3 左盖............................................................................................................................................................................................... F-5
4.1.4 右后盖........................................................................................................................................................................................... F-5
4.1.5 右下盖........................................................................................................................................................................................... F-6
4.1.6 后盖............................................................................................................................................................................................... F-6
4.1.7 扫描器右盖................................................................................................................................................................................... F-6
4.1.8 出纸后盖....................................................................................................................................................................................... F-6
4.1.9 出纸盘 (左) / 出纸盘 (右).................................................................................................................................................. F-7
4.1.10 控制面板左盖............................................................................................................................................................................... F-7
4.1.11 控制面板....................................................................................................................................................................................... F-7
4.1.12 稿台组件....................................................................................................................................................................................... F-8
4.2 单元........................................................................................................................................................................................F-10
4.2.1 纸盒 1.......................................................................................................................................................................................... F-10
4.2.2 手送纸盒..................................................................................................................................................................................... F-10
4.2.3 PH 单元 (PH)..........................................................................................................................................................................F-11
4.2.4 CIS 模块 (CIS)....................................................................................................................................................................... F-13
4.2.5 扫描器单元................................................................................................................................................................................. F-14
4.2.6 出纸单元..................................................................................................................................................................................... F-15
4.3 电路板....................................................................................................................................................................................F-16
4.3.1 MFP 板 (MFPB)..................................................................................................................................................................... F-16
4.3.2 DC 电源 (DCPU)................................................................................................................................................................... F-17
4.3.3 高压单元 (HV)....................................................................................................................................................................... F-17
4.4 马达........................................................................................................................................................................................F-18
iv
4.4.1 扫描器马达 (M1)................................................................................................................................................................... F-18
4.4.2 主马达 (M2)........................................................................................................................................................................... F-19
4.4.3 反转马达 (M3)....................................................................................................................................................................... F-19
4.4.4 碳粉供应马达 (M5)............................................................................................................................................................... F-19
4.5 离合器....................................................................................................................................................................................F-20
4.5.1 对位离合器 (CL1)................................................................................................................................................................. F-20
4.5.2 纸盒 1 进纸离合器 (CL2)..................................................................................................................................................... F-21
4.5.3 手送进纸离合器 (CL3)......................................................................................................................................................... F-21
4.6 风扇马达 ................................................................................................................................................................................F-22
4.6.1 吸气风扇 (FM1)..................................................................................................................................................................... F-22
4.7 其它........................................................................................................................................................................................F-22
4.7.1 臭氧滤网..................................................................................................................................................................................... F-22
4.7.2 手送进纸拾纸磁铁 (SD1)..................................................................................................................................................... F-23
4.7.3 温度 / 湿度传感器 (TEM/HUM)........................................................................................................................................... F-23
4.7.4 英制 / 公制传感器 (PS12)组件 (仅限拉丁美洲和亚太地区)........................................................................................ F-24
5. 自动双面输稿器 (DF-633).............................................................................................................................................................F-25
5.1 前盖 (DF-633)....................................................................................................................................................................F-25
5.2 后盖 (DF-633)....................................................................................................................................................................F-25
5.3 进纸纸盒 (DF-633).............................................................................................................................................................F-25
5.4 自动双面输稿器 (DF-633)..................................................................................................................................................F-26
5.5 进纸单元 (DF-633).............................................................................................................................................................F-27
5.6 进纸马达组件 (DF-633)......................................................................................................................................................F-28
5.7 DF 控制板 (DFCB)(DF-633)...........................................................................................................................................F-29
5.8 进纸马达 (M1)(DF-633)..................................................................................................................................................F-30
5.9 进纸离合器 (CL1)(DF-633).............................................................................................................................................F-30
5.10 对位离合器 (CL2)(DF-633).............................................................................................................................................F-31
6. PF-507 .............................................................................................................................................................................................F-32
6.1 纸盒 (PF-507).....................................................................................................................................................................F-32
6.2 后盖 (PF-507).....................................................................................................................................................................F-32
6.3 通用纸盒 (PF-507).............................................................................................................................................................F-32
6.4 PF 驱动板 (PFDB)(PF-507)...........................................................................................................................................F-34
6.5 纸张尺寸检测开关 (S1)(PF-507)....................................................................................................................................F-35
6.6 进纸电磁铁 (SD1)(PF-507)............................................................................................................................................F-35
7. AD-509.............................................................................................................................................................................................F-37
7.1 后盖........................................................................................................................................................................................F-37
7.2 自动双面器单元......................................................................................................................................................................F-37
7.3 AD 驱动板 (ADDB).............................................................................................................................................................F-38
7.4 AD 马达 (M1).....................................................................................................................................................................F-38
7.5 冷却风扇 (FM2)..................................................................................................................................................................F-38
8. FK-510/MK-750................................................................................................................................................................................F-39
8.1 传真电路板 (FAXB)(FK-510)..........................................................................................................................................F-39
8.2 扩展控制面板 (EPB)(MK-750)........................................................................................................................................F-39
8.3 扬声器 (SP1)......................................................................................................................................................................F-39
G 机械调整 ............................................................................................................................ G-1
1. 高级检查............................................................................................................................................................................................ G-1
2. 自动双面输稿器 (DF-633).............................................................................................................................................................. G-2
2.1 ADF 歪斜调整 ......................................................................................................................................................................... G-2
3. PF-507 .............................................................................................................................................................................................. G-5
3.1 纸张基准位置 .......................................................................................................................................................................... G-5
3.1.1 用途...............................................................................................................................................................................................G-5
3.1.2 规格...............................................................................................................................................................................................G-5
3.1.3 步骤...............................................................................................................................................................................................G-5
v H 效用模式 / 维修模式 .......................................................................................................... H-1
1. 效用................................................................................................................................................................................................... H-1
1.1 效用模式列表 .......................................................................................................................................................................... H-1
1.2 启动 / 退出............................................................................................................................................................................... H-7
1.2.1 启动步骤.......................................................................................................................................................................................H-7
1.2.2 退出步骤.......................................................................................................................................................................................H-7
1.3 MACHINE SETTING (机器设置)......................................................................................................................................... H-7
1.3.1 AUTO PANEL RESET (自动面板复位).................................................................................................................................H-7
1.3.2 SLEEP MODE (睡眠模式)......................................................................................................................................................H-7
1.3.3 AUTO SHUT TIME (自动关闭时间).....................................................................................................................................H-7
1.3.4 DENSITY (ADF) (浓度 (ADF))..........................................................................................................................................H-7
1.3.5 DENSITY (BOOK) (浓度 (书本))......................................................................................................................................H-7
1.3.6 PRINT DENSITY (打印浓度).................................................................................................................................................H-8
1.3.7 LCD CONTRAST (LCD 对比度)...........................................................................................................................................H-8
1.3.8 KEY SPEED SETTING (按键速度设置)...............................................................................................................................H-8
1.3.9 LANGUAGE (语言)................................................................................................................................................................H-8
1.3.10 BUZZER VOLUME (蜂鸣器音量).........................................................................................................................................H-9
1.3.11 INITIAL MODE (初始模式).................................................................................................................................................H-11
1.3.12 SCAN THRESHOLD (扫描阈值).........................................................................................................................................H-12
1.4 PAPER SOURCE SETUP (纸张来源设置)........................................................................................................................ H-12
1.4.1 TRAY1 (纸盒 1).....................................................................................................................................................................H-12
1.4.2 TRAY2/TRAY3/TRAY4/TRAY5 (纸盒 2/ 纸盒 3/ 纸盒 4/ 纸盒 5).....................................................................................H-12
1.5 CUSTOM SIZE MEMORY (自定义尺寸存储器)................................................................................................................ H-13
1.5.1 CUSTOM SIZE MEMORY (自定义尺寸存储器)................................................................................................................H-13
1.6 DRUM DEHUMIDIFY (感光鼓除湿)................................................................................................................................... H-13
1.6.1 用途.............................................................................................................................................................................................H-13
1.6.2 步骤.............................................................................................................................................................................................H-13
1.7 ADMIN. MANAGEMENT (管理员管理)............................................................................................................................. H-13
1.7.1 ADMINISTRATOR NO. (管理员编号)................................................................................................................................H-13
1.7.2 DISPLAY AUTO SHUT (显示自动关闭).............................................................................................................................H-13
1.7.3 SLEEP SHIFT (睡眠移位).....................................................................................................................................................H-13
1.7.4 PWR CONS. SLEEP (功耗睡眠)..........................................................................................................................................H-14
1.7.5 ACCOUNT TRACK (账户跟踪)...........................................................................................................................................H-14
1.7.6 REMOTE MONITOR (远程监控).........................................................................................................................................H-14
1.7.7 NETWORK SETTING - IP ADDRESS SETTING (网络设置 ——IP 地址设置)..............................................................H-16
1.7.8 NETWORK SETTING - IPv6 (网络设置 ——IPv6)...........................................................................................................H-16
1.7.9 NETWORK SETTING - DNS CONFIG. (网络设置 ——DNS 配置).................................................................................H-17
1.7.10 NETWORK SETTING - WEB SETTING (网络设置 ——WEB 设置)..............................................................................H-17
1.7.11 NETWORK SETTING - LPD SETTING (网络设置 ——LPD 设置).................................................................................H-17
1.7.12 NETWORK SETTING - SLP SETTING (网络设置 ——SLP 设置)..................................................................................H-18
1.7.13 NETWORK SETTING - SNMP SETTING (网络设置 ——SNMP 设置)..........................................................................H-18
1.7.14 NETWORK SETTING - AUTO GET TIME (网络设置 —— 自动获取时间)...................................................................H-18
1.7.15 E-MAIL SETTING 1 (电子邮件设置 1)...............................................................................................................................H-19
1.7.16 E-MAIL SETTING 2 (电子邮件设置 2)...............................................................................................................................H-21
1.7.17 LDAP SETTING (LDAP 设置).............................................................................................................................................H-23
1.7.18 COMM. SETTING (通用设置).............................................................................................................................................H-25
1.7.19 USER SETTING (用户设置).................................................................................................................................................H-25
1.7.20 SCAN TO USB (扫描到 USB)..............................................................................................................................................H-26
1.7.21 MOBILE PRINT (移动打印).................................................................................................................................................H-27
1.7.22 DISPLAY PRINTER OWNER (显示打印机所有者)...........................................................................................................H-27
1.8 COPY SETTING (复印设置) 1.......................................................................................................................................... H-27
1.8.1 PAPER PRIORITY (纸张优先级).........................................................................................................................................H-27
1.8.2 QUALITY PRIORITY (质量优先级)...................................................................................................................................H-27
1.8.3 DENSITY PRIORITY (浓度优先级)....................................................................................................................................H-27
1.8.4 DENSITY LEVEL (浓度等级)..............................................................................................................................................H-27
1.8.5 DUPLEX PRIORITY (双面优先级).....................................................................................................................................H-28
1.8.6 OUTPUT BIND POS. (输出装订位置).................................................................................................................................H-28
1.8.7 ORIG. BINDING POS. (原稿装订位置)...............................................................................................................................H-28
1.8.8 BINDING POSITION (装订位置)........................................................................................................................................H-28
1.8.9 MARGIN SETTING (边距设置)...........................................................................................................................................H-28
1.8.10 ERASE SETTING (消除设置)..............................................................................................................................................H-29
1.8.11 OUTER ERASE (外部消除)..................................................................................................................................................H-29
1.8.12 SMALL ORIGINAL (小型原稿)...........................................................................................................................................H-29
1.9 COPY SETTING (复印设置) 2.......................................................................................................................................... H-29
1.9.1 COPY PRIORITY (复印优先级)..........................................................................................................................................H-29
1.9.2 OUTPUT PRIORITY (输出优先级).....................................................................................................................................H-29
1.9.3 CRISSCROSS MODE (交叉模式)........................................................................................................................................H-30
1.9.4 4IN1 COPY ORDER (四合一复印顺序)..............................................................................................................................H-30
1.9.5 MIXED ORIGINAL (混合原稿)...........................................................................................................................................H-30
1.9.6 ORIG.DIRECTION (原稿方向).............................................................................................................................................H-30
1.9.7 BOOK SEPARATION (书本分离)........................................................................................................................................H-30
1.9.8 STAMP (印记)........................................................................................................................................................................H-30
1.9.9 PAGE FORMAT (页面格式).................................................................................................................................................H-31
1.9.10 DATE&TIME FORMAT (日期和时间格式)........................................................................................................................H-31
1.10 DIAL REGISTRATION (拨号注册)..................................................................................................................................... H-31
1.10.1 ONE-TOUCH DIAL (单触拨号)...........................................................................................................................................H-31
1.10.2 SPEED DIAL (快速拨号)......................................................................................................................................................H-31
1.10.3 GROUP DIAL (群组拨号)....................................................................................................................................................H-31
1.10.4 PROGRAM DIAL (程序拨号)..............................................................................................................................................H-31
1.11 FAX REGISTRATION (传真注册)...................................................................................................................................... H-32
1.11.1 MAILBOX (邮箱)..................................................................................................................................................................H-32
1.11.2 RELAY BOX (中继 Box).......................................................................................................................................................H-32
1.12 FAX TX OPERATION (传真发送操作)............................................................................................................................... H-32
1.12.1 DENSITY LEVEL (浓度等级)..............................................................................................................................................H-32
1.12.2 QUALITY PRIORITY (质量优先级)...................................................................................................................................H-33
1.12.3 DEFAULT TX (默认发送).....................................................................................................................................................H-33
1.12.4 HEADER (页眉)....................................................................................................................................................................H-33
1.12.5 CONFIRM FAX NO. (确认传真号码)..................................................................................................................................H-33
1.13 FAX RX OPERATION (传真接收操作)............................................................................................................................... H-33
1.13.1 MEMORY RX MODE (记忆接收模式)...............................................................................................................................H-33
1.13.2 NO. of RINGS (响铃次数)....................................................................................................................................................H-34
1.13.3 REDUCTION RX (缩小接收)...............................................................................................................................................H-34
1.13.4 RX PRINT (接收打印)..........................................................................................................................................................H-41
1.13.5 RX MODE (接收模式)..........................................................................................................................................................H-41
1.13.6 FORWARD (转发).................................................................................................................................................................H-42
1.13.7 FOOTER (页脚).....................................................................................................................................................................H-42
1.13.8 SELECT TRAY (选择纸盒)..................................................................................................................................................H-42
1.13.9 CLOSED NETWORK (闭合网络)........................................................................................................................................H-43
1.14 REPORTING (报告).......................................................................................................................................................... H-43
1.14.1 ACTIVITY REPORT (活动报告)..........................................................................................................................................H-43
1.14.2 RESERVATION REPORT (保留报告)..................................................................................................................................H-43
1.14.3 TX RESULT REPORT (发送结果报告)...............................................................................................................................H-43
1.14.4 RX RESULT REPORT (接收结果报告)...............................................................................................................................H-43
1.15 SCAN SETTING (扫描设置).............................................................................................................................................. H-43
1.15.1 RESOLUTION (分辨率).......................................................................................................................................................H-43
1.15.2 IMAGE FORMAT (图像格式)..............................................................................................................................................H-44
1.15.3 BW CODING METHOD (黑白编码方式)...........................................................................................................................H-44
1.15.4 COLOR SETTING (颜色设置).............................................................................................................................................H-44
1.16 COMFIRM MODE (确认模式)........................................................................................................................................... H-44
1.16.1 TOTAL PAGE (总页数).........................................................................................................................................................H-44
vi
vii
1.16.2 TX/RX RESULT (发送 / 接收结果)......................................................................................................................................H-44
1.16.3 PRINT REPORT (打印报告).................................................................................................................................................H-45
2. 维修模式.......................................................................................................................................................................................... H-46
2.1 维修模式列表 ........................................................................................................................................................................ H-46
2.2 启动 / 退出............................................................................................................................................................................. H-49
2.2.1 启动步骤.....................................................................................................................................................................................H-49
2.2.2 退出步骤.....................................................................................................................................................................................H-49
2.2.3 更改 SERVICE MODE (维修模式)功能中的设置值 ........................................................................................................H-49
2.3 SERVICE'S CHOICE (维修选择)...................................................................................................................................... H-49
2.3.1 MARKETING AREA (销售地区).........................................................................................................................................H-49
2.3.2 SHIPMENT (运输).................................................................................................................................................................H-49
2.3.3 ENABLE AUTO SHUT (启用自动关闭).............................................................................................................................H-49
2.3.4 MAINTENANCE COUNT. (维修保养计数器)....................................................................................................................H-50
2.3.5 IU LIFE STOP MODE (IU 寿命停止模式)..........................................................................................................................H-50
2.3.6 ID ADJUST (ID 调整)...........................................................................................................................................................H-50
2.3.7 VG ADJUST (VG 调整)........................................................................................................................................................H-50
2.3.8 TRANSFER (PLAIN) (转印 (普通纸)).............................................................................................................................H-50
2.3.9 TRANSFER (RECYCLE) (转印 (再生纸))......................................................................................................................H-51
2.3.10 TRANSFER (CARD1) (转印 (卡纸 1))............................................................................................................................H-51
2.3.11 TRANSFER (CARD2) (转印 (卡纸 1))............................................................................................................................H-51
2.3.12 TRANSFER (OHP) (转印 (OHP))....................................................................................................................................H-51
2.3.13 TRANSFER (ENVELOPE) (转印 (信封))........................................................................................................................H-51
2.3.14 TRANSFER (PLAIN-D) (转印 (普通纸 D)).....................................................................................................................H-51
2.3.15 TRANSFER (RECY.-D) (转印 (再生纸 D)).....................................................................................................................H-51
2.3.16 TRANSFER (CARD1-D) (转印 (卡纸 1 D))....................................................................................................................H-52
2.3.17 TRANSFER (CARD2-D) (转印 (卡纸 2 D))....................................................................................................................H-52
2.3.18 FUSER TEMP.(PLAIN) (定影温度 (普通纸)).................................................................................................................H-52
2.3.19 FUSER TEMP. (CARD1) (定影温度 (卡纸 1))................................................................................................................H-52
2.3.20 FUSER TEMP. (CARD2) (定影温度 (卡纸 2))................................................................................................................H-53
2.3.21 FUSER TEMP.(OHP) (定影温度 (OHP)).........................................................................................................................H-53
2.3.22 FUSER TEMP.(ENV.) (定影温度 (信封)).........................................................................................................................H-53
2.3.23 SMART FUSER (智能定影)..................................................................................................................................................H-54
2.3.24 LEADING EDGE (主缘).......................................................................................................................................................H-54
2.3.25 TRAILING EDGE (尾缘)......................................................................................................................................................H-54
2.3.26 VERTICAL EDGE (垂直边缘).............................................................................................................................................H-55
2.3.27 LOOP Ad. (TRAY1) (波幅调整 (纸盒 1))........................................................................................................................H-55
2.3.28 LOOP Ad. (TRAY2-5) (波幅调整 (纸盒 2-5)).................................................................................................................H-55
2.3.29 LOOP Ad.(DUPLEX) (波幅调整 (双面)).........................................................................................................................H-55
2.3.30 LOOP Ad. (BYPASS) (波幅调整 (手送进纸)).................................................................................................................H-56
2.3.31 FLS PAPER SIZE (FLS 纸尺寸)...........................................................................................................................................H-56
2.3.32 FLS/LEGAL CHANGE (FLS/LEGAL 更改)........................................................................................................................H-56
2.3.33 TX SPEED (发送速度)..........................................................................................................................................................H-56
2.3.34 RX SPEED (接收速度)..........................................................................................................................................................H-56
2.3.35 TX LEVEL (发送等级)..........................................................................................................................................................H-57
2.3.36 DTMF LEVEL (DTMF 等级)................................................................................................................................................H-57
2.3.37 CNG LEVEL (CNG 等级).....................................................................................................................................................H-57
2.3.38 CED LEVEL (CED 等级)......................................................................................................................................................H-57
2.3.39 ECM MODE (ECM 模式).....................................................................................................................................................H-57
2.3.40 CODING SCHEME (编码方案)............................................................................................................................................H-57
2.3.41 VOIP ...........................................................................................................................................................................................H-58
2.3.42 REPORT DESTINATION (报告目的地)..............................................................................................................................H-58
2.3.43 TONER EMPTY REPORT (碳粉用尽报告).........................................................................................................................H-58
2.3.44 IU LIFE REPORT (IU 寿命报告)..........................................................................................................................................H-58
2.3.45 MAINTENANCE REPORT (维修保养报告).......................................................................................................................H-59
2.3.46 PROTOCOL REPORT (协议报告).......................................................................................................................................H-59
2.3.47 CIS APS SIZE (CIS APS 尺寸).............................................................................................................................................H-59
2.3.48 GDI TIMEOUT (GDI 超时)..................................................................................................................................................H-60
2.3.49 ERASER INSTALL (消电灯安装)........................................................................................................................................H-60
2.3.50 SUCTION FAN (吸气风扇)...................................................................................................................................................H-60
2.3.51 LANGUAGE GROUP (语言群组)........................................................................................................................................H-60
2.3.52 HV B(AC) CLK (HV B (AC)时钟)..................................................................................................................................H-60
2.3.53 PH STANDBY MODE (PH 待机模式).................................................................................................................................H-61
2.4 ADJUST (调整)................................................................................................................................................................. H-61
2.4.1 PRN MAIN (TRAY1) (打印主 (纸盒 1))..........................................................................................................................H-61
2.4.2 PRN MAIN (BYPASS) (打印主 (手送进纸))...................................................................................................................H-62
2.4.3 PRN MAIN (TRAY2) (打印主 (纸盒 2))..........................................................................................................................H-62
2.4.4 PRN MAIN (TRAY3) (打印主 (纸盒 3))..........................................................................................................................H-63
2.4.5 PRN MAIN (TRAY4) (打印主 (纸盒 4))..........................................................................................................................H-64
2.4.6 PRN MAIN (TRAY5) (打印主 (纸盒 5))..........................................................................................................................H-65
2.4.7 PRN MAIN (DUPLEX) (打印主 (双面))..........................................................................................................................H-66
2.4.8 PRN SUB (TRAY1-P) (打印副 (纸盒 1 P))......................................................................................................................H-67
2.4.9 PRN SUB (TRAY1-R) (打印副 (纸盒 1 R)).....................................................................................................................H-67
2.4.10 PRN SUB (TRAY1-C1) (打印副 (纸盒 1 C1)).................................................................................................................H-68
2.4.11 PRN SUB (TRAY1-C2) (打印副 (纸盒 1 C2)).................................................................................................................H-69
2.4.12 PRN SUB (TRAY1-O) (打印副 (纸盒 1 O)).....................................................................................................................H-70
2.4.13 PRN SUB (TRAY1-E) (打印副 (纸盒 1 E))......................................................................................................................H-71
2.4.14 PRN SUB (BYPASS-P) (打印副 (手送进纸 P))...............................................................................................................H-71
2.4.15 PRN SUB (BYPASS-R) (打印副 (手送进纸 R))..............................................................................................................H-72
2.4.16 PRN SUB (BYPASS-C1) (打印副 (手送进纸 C1))..........................................................................................................H-73
2.4.17 PRN SUB (BYPASS-C2) (打印副 (手送进纸 C2))..........................................................................................................H-74
2.4.18 PRN SUB (BYPASS-O) (打印副 (手送进纸 O)).............................................................................................................H-75
2.4.19 PRN SUB (BYPASS-E) (打印副 (手送进纸 E))..............................................................................................................H-76
2.4.20 PRN SUB (TRAY2) (打印副 (纸盒 2)).............................................................................................................................H-76
2.4.21 PRN SUB (TRAY3) (打印副 (纸盒 3)).............................................................................................................................H-77
2.4.22 PRN SUB (TRAY4) (打印副 (纸盒 4)).............................................................................................................................H-78
2.4.23 PRN SUB (TRAY5) (打印副 (纸盒 5)).............................................................................................................................H-79
2.4.24 PRN SUB (DUPLEX) (打印副 (双面)).............................................................................................................................H-80
2.4.25 CIS MAIN ZOOM (CIS 主缩放)...........................................................................................................................................H-81
2.4.26 CIS SUB ZOOM (CIS 副缩放)..............................................................................................................................................H-81
2.4.27 CIS MAIN REGIST (CIS 主对位)........................................................................................................................................H-82
2.4.28 CIS SUB REGIST (CIS 副对位)...........................................................................................................................................H-83
2.4.29 ADF SUB ZOOM (ADF 副缩放)..........................................................................................................................................H-83
2.4.30 ADF MAIN ZOOM (ADF 主缩放).......................................................................................................................................H-84
2.4.31 ADF SUB REGIST1 (ADF 副对位 1)...................................................................................................................................H-85
2.4.32 ADF SUB REGIST2 (ADF 副对位 2)...................................................................................................................................H-86
2.4.33 ADF MAIN REGIST1 (ADF 主对位 1)................................................................................................................................H-87
2.4.34 ADF MAIN REGIST2 (ADF 主对位 2)................................................................................................................................H-88
2.4.35 ADF REG.LOOP1 (波幅 1)....................................................................................................................................................H-89
2.4.36 ADF REG.LOOP2 (波幅 2)....................................................................................................................................................H-90
2.4.37 TCR GAIN (TCR 获取).........................................................................................................................................................H-90
2.4.38 MODEL SETTING (型号设置).............................................................................................................................................H-90
2.4.39 CUSTOMER ID (客户 ID)....................................................................................................................................................H-90
2.4.40 GROUP_S ID (群组 _S ID)...................................................................................................................................................H-90
2.5 COUNTER (计数器).......................................................................................................................................................... H-91
2.5.1 TOTAL COUNTER (总计数器)............................................................................................................................................H-91
2.5.2 SIZE COUNTER (尺寸计数器)............................................................................................................................................H-91
2.5.3 PM COUNTER (PM 计数器)................................................................................................................................................H-91
2.5.4 MAINTENANCE COUNT. (维修保养计数器)....................................................................................................................H-91
2.5.5 SUPPLIES COUNTER (耗材计数器)...................................................................................................................................H-91
2.5.6 APPLICATION COUNT. (应用计数器)...............................................................................................................................H-92
viii
ix
2.5.7 SCAN COUNTER (扫描计数器)..........................................................................................................................................H-92
2.5.8 PAPER SIZE COUNTER (纸张尺寸计数器).......................................................................................................................H-92
2.5.9 MISFEED COUNTER (卡纸计数器)....................................................................................................................................H-92
2.5.10 TROUBLE COUNTER (故障计数器)..................................................................................................................................H-92
2.5.11 CAUTION COUNTER (警告计数器)...................................................................................................................................H-92
2.6 DISPLAY (显示)................................................................................................................................................................. H-92
2.6.1 TONER DENSITY (碳粉浓度).............................................................................................................................................H-92
2.6.2 FUSER TEMPERATURE (定影温度)..................................................................................................................................H-93
2.6.3 TRANSCRIPT CURRENT (转印电流)................................................................................................................................H-93
2.6.4 TCR GAIN (TCR 获取).........................................................................................................................................................H-93
2.6.5 PROCESS CONTROL (处理控制).......................................................................................................................................H-93
2.6.6 ENVIRONMENTAL (环境)..................................................................................................................................................H-93
2.6.7 MAIN F/W VER. (主固件版本)............................................................................................................................................H-93
2.6.8 MAIN F/W VER. (引擎固件版本)........................................................................................................................................H-93
2.6.9 MAIN RAM SIZE (主 RAM 容量).......................................................................................................................................H-93
2.6.10 SERIAL NO. (序列号)...........................................................................................................................................................H-93
2.6.11 CUSTOMER ID (客户 ID)....................................................................................................................................................H-93
2.7 功能....................................................................................................................................................................................... H-93
2.7.1 PAPER FEED TEST (进纸测试)...........................................................................................................................................H-93
2.7.2 PROCESS CHECK (处理检查).............................................................................................................................................H-94
2.7.3 TCR AUTO ADJUST (TCR 自动调整)................................................................................................................................H-94
2.7.4 PRN TEST PATTERN (打印测试模式)................................................................................................................................H-94
2.7.5 ADF FEED TEST (ADF 进纸测试)......................................................................................................................................H-95
2.7.6 COPY ADF GLASS (复印 ADF 玻璃).................................................................................................................................H-95
2.7.7 FAX RES. COPY TEST (传真分辨率复印测试).................................................................................................................H-95
2.7.8 SCAN TEST (扫描测试).......................................................................................................................................................H-96
2.7.9 TONER SUPPLY (碳粉供应)................................................................................................................................................H-96
2.7.10 OUTER ERASE CHECK (外部消除检查)...........................................................................................................................H-96
2.8 SOFT SWITCH (软开关)................................................................................................................................................... H-97
2.9 REPORT (报告)................................................................................................................................................................ H-97
2.9.1 SERVICE DATA LIST (维修数据列表)...............................................................................................................................H-97
2.9.2 ERROR CODE LIST (错误代码列表)..................................................................................................................................H-97
2.9.3 T.30 PROTOCOL LIST (T.30 协议列表)..............................................................................................................................H-97
2.9.4 SETTING DATA LIST (设置数据列表)...............................................................................................................................H-98
2.10 DEVICE REPORT TX (设备报告发送).............................................................................................................................. H-98
2.10.1 文件名.........................................................................................................................................................................................H-98
2.10.2 E-MAIL SETTING (电子邮件设置).....................................................................................................................................H-98
2.10.3 TX DESTINATION (发送目的地)........................................................................................................................................H-99
2.10.4 TX SCHEDULE (发送计划).................................................................................................................................................H-99
2.10.5 TX METHOD (发送方式).....................................................................................................................................................H-99
2.10.6 TX REPORT (发送报告).......................................................................................................................................................H-99
2.10.7 TX LOG (发送日志)............................................................................................................................................................H-100
2.10.8 TX TEST (发送测试)...........................................................................................................................................................H-100
2.10.9 DOWNLOAD TO USB (下载至 USB)...............................................................................................................................H-100
2.11 ADMIN. REGISTRATION (管理员注册).......................................................................................................................... H-100
2.11.1 用途...........................................................................................................................................................................................H-100
2.11.2 默认设置...................................................................................................................................................................................H-100
2.11.3 步骤...........................................................................................................................................................................................H-100
2.12 FIXED ZOOM CHANGE (固定缩放更改)........................................................................................................................ H-100
2.12.1 用途...........................................................................................................................................................................................H-100
2.12.2 步骤...........................................................................................................................................................................................H-100
2.12.3 固定缩放比率的默认值和设置范围.......................................................................................................................................H-101
2.13 FACTORY TEST (出厂测试)............................................................................................................................................ H-101
2.13.1 SIGNAL TEST (信号测试).................................................................................................................................................H-101
2.13.2 RELAY TEST (中继测试)...................................................................................................................................................H-101
x
2.13.3 Dial Test (拨号测试)............................................................................................................................................................H-101
2.13.4 VOLUME TEST (音量测试)...............................................................................................................................................H-102
2.13.5 PANEL BUZZER TEST (面板蜂鸣器测试).......................................................................................................................H-102
2.13.6 RAM TEST (RAM 测试).....................................................................................................................................................H-102
2.14 CLEAR DATA (清除数据)................................................................................................................................................. H-102
2.14.1 DRAM CLEAR (DRAM 清除)...........................................................................................................................................H-102
2.14.2 FLASH ROM CLEAR (闪存存储器清空)..........................................................................................................................H-102
2.14.3 MEMORY CLEAR (存储器清空).......................................................................................................................................H-102
2.14.4 TOTAL CLEAR (总清零)....................................................................................................................................................H-103
2.14.5 PM COUNTER (PM 计数器)..............................................................................................................................................H-103
2.14.6 MAINTENANCE COUNT. (维修保养计数器)..................................................................................................................H-104
2.14.7 SUPPLIES COUNTER (耗材计数器).................................................................................................................................H-104
2.14.8 APPLICATION COUNT. (应用计数器).............................................................................................................................H-104
2.14.9 SCAN COUNTER (扫描计数器)........................................................................................................................................H-104
2.14.10 PAPER SIZE COUNTER (纸张尺寸计数器).....................................................................................................................H-104
2.14.11 MISFEED COUNTER (卡纸计数器)..................................................................................................................................H-104
2.14.12 TROUBLE COUNTER (故障计数器)................................................................................................................................H-104
2.14.13 CAUTION COUNTER (警告计数器).................................................................................................................................H-104
3. SECURITY MODE (安全模式).................................................................................................................................................. H-105
3.1 安全模式列表 ...................................................................................................................................................................... H-105
3.2 启动 / 退出........................................................................................................................................................................... H-105
3.2.1 启动步骤...................................................................................................................................................................................H-105
3.2.2 退出步骤...................................................................................................................................................................................H-105
3.3 SECURITY (安全)........................................................................................................................................................... H-105
3.3.1 TOTAL COUNTER (总计数器)..........................................................................................................................................H-105
3.3.2 SIZE COUNTER (尺寸计数器)..........................................................................................................................................H-105
3.3.3 PLUG-IN COUNTER (插件程序计数器)...........................................................................................................................H-105
4. SOFT SWITCH SET (软开关设置)............................................................................................................................................ H-106
4.1 说明..................................................................................................................................................................................... H-106
4.2 默认设置 ............................................................................................................................................................................. H-106
4.2.1 软开关列表...............................................................................................................................................................................H-106
4.2.2 每个销售地区的默认软开关设置 (销售地区 1)................................................................................................................H-110
4.2.3 每个销售地区的默认软开关设置 (销售地区 2)................................................................................................................ H-111
4.2.4 每个销售地区的默认软开关设置 (销售地区 3)................................................................................................................H-113
4.2.5 每个销售地区的默认软开关设置 (销售地区 4)................................................................................................................H-114
4.2.6 每个销售地区的默认软开关设置 (销售地区 5)................................................................................................................H-115
4.2.7 每个销售地区的默认软开关设置 (销售地区 6)................................................................................................................H-117
4.2.8 每个销售地区的默认软开关设置 (销售地区 7)................................................................................................................H-118
4.2.9 每个销售地区的默认软开关设置 (销售地区 8)................................................................................................................H-121
4.2.10 每个销售地区的默认软开关设置 (销售地区 9)................................................................................................................H-122
4.2.11 每个销售地区的默认软开关设置 (销售地区 10)..............................................................................................................H-124
4.2.12 每个销售地区的默认软开关设置 (销售地区 11)..............................................................................................................H-125
4.2.13 每个销售地区的默认软开关设置 (销售地区 12)..............................................................................................................H-127
4.3 软开关定义.......................................................................................................................................................................... H-128
4.3.1 SOFT SWITCH (软开关):#01 ..........................................................................................................................................H-128
4.3.2 SOFT SWITCH (软开关):#02 ..........................................................................................................................................H-128
4.3.3 SOFT SWITCH (软开关):#03 ..........................................................................................................................................H-129
4.3.4 SOFT SWITCH (软开关):#04 ..........................................................................................................................................H-129
4.3.5 SOFT SWITCH (软开关):#05 ..........................................................................................................................................H-130
4.3.6 SOFT SWITCH (软开关):#06 ..........................................................................................................................................H-131
4.3.7 SOFT SWITCH (软开关):#07 ..........................................................................................................................................H-131
4.3.8 SOFT SWITCH (软开关):#08 ..........................................................................................................................................H-131
4.3.9 SOFT SWITCH (软开关):#09 ..........................................................................................................................................H-132
4.3.10 SOFT SWITCH (软开关):#10 ..........................................................................................................................................H-132
4.3.11 SOFT SWITCH (软开关):#11...........................................................................................................................................H-133
xi
4.3.12 SOFT SWITCH (软开关):#12 ..........................................................................................................................................H-133
4.3.13 SOFT SWITCH (软开关):#13 ..........................................................................................................................................H-134
4.3.14 SOFT SWITCH (软开关):#14 ..........................................................................................................................................H-134
4.3.15 SOFT SWITCH (软开关):#15 ..........................................................................................................................................H-135
4.3.16 SOFT SWITCH (软开关):#16 ..........................................................................................................................................H-135
4.3.17 SOFT SWITCH (软开关):#17 ..........................................................................................................................................H-135
4.3.18 SOFT SWITCH (软开关):#18 ..........................................................................................................................................H-136
4.3.19 SOFT SWITCH (软开关):#19 ..........................................................................................................................................H-136
4.3.20 SOFT SWITCH (软开关):#20 ..........................................................................................................................................H-137
4.3.21 SOFT SWITCH (软开关):#21 ..........................................................................................................................................H-137
4.3.22 SOFT SWITCH (软开关):#22 ..........................................................................................................................................H-138
4.3.23 SOFT SWITCH (软开关):#23 ..........................................................................................................................................H-139
4.3.24 SOFT SWITCH (软开关):#24 ..........................................................................................................................................H-139
4.3.25 SOFT SWITCH (软开关):#25 ..........................................................................................................................................H-139
4.3.26 SOFT SWITCH (软开关):#26 ..........................................................................................................................................H-140
4.3.27 SOFT SWITCH (软开关):#27 ..........................................................................................................................................H-140
4.3.28 SOFT SWITCH (软开关):#28 ..........................................................................................................................................H-140
4.3.29 SOFT SWITCH (软开关):#29 ..........................................................................................................................................H-141
4.3.30 SOFT SWITCH (软开关):#30 ..........................................................................................................................................H-141
4.3.31 SOFT SWITCH (软开关):#31 ..........................................................................................................................................H-142
4.3.32 SOFT SWITCH (软开关):#32 ..........................................................................................................................................H-142
4.3.33 SOFT SWITCH (软开关):#33 ..........................................................................................................................................H-143
4.3.34 SOFT SWITCH (软开关):#34 ..........................................................................................................................................H-143
4.3.35 SOFT SWITCH (软开关):#35 ..........................................................................................................................................H-143
4.3.36 SOFT SWITCH (软开关):#36 ..........................................................................................................................................H-144
4.3.37 SOFT SWITCH (软开关):#37 ..........................................................................................................................................H-144
4.3.38 SOFT SWITCH (软开关):#38 ..........................................................................................................................................H-144
4.3.39 SOFT SWITCH (软开关):#39 ..........................................................................................................................................H-145
4.3.40 SOFT SWITCH (软开关):#40 ..........................................................................................................................................H-145
4.3.41 SOFT SWITCH (软开关):#41 ..........................................................................................................................................H-146
4.3.42 SOFT SWITCH (软开关):#42 ..........................................................................................................................................H-147
4.3.43 SOFT SWITCH (软开关):#43 ..........................................................................................................................................H-147
4.3.44 SOFT SWITCH (软开关):#44 ..........................................................................................................................................H-147
4.3.45 SOFT SWITCH (软开关):#45 ..........................................................................................................................................H-147
4.3.46 SOFT SWITCH (软开关):#46 ..........................................................................................................................................H-148
4.3.47 SOFT SWITCH (软开关):#47 ..........................................................................................................................................H-148
4.3.48 SOFT SWITCH (软开关):#48 ..........................................................................................................................................H-148
4.3.49 SOFT SWITCH (软开关):#49 ..........................................................................................................................................H-149
4.3.50 SOFT SWITCH (软开关):#50 ..........................................................................................................................................H-149
4.3.51 SOFT SWITCH (软开关):#51 ..........................................................................................................................................H-150
4.3.52 SOFT SWITCH (软开关):#52 ..........................................................................................................................................H-150
4.3.53 SOFT SWITCH (软开关):#53 ..........................................................................................................................................H-151
4.3.54 SOFT SWITCH (软开关):#54 ..........................................................................................................................................H-151
4.3.55 SOFT SWITCH (软开关):#55 ..........................................................................................................................................H-151
4.3.56 SOFT SWITCH (软开关):#56 ..........................................................................................................................................H-152
4.3.57 SOFT SWITCH (软开关):#57 ..........................................................................................................................................H-152
4.3.58 SOFT SWITCH (软开关):#58 ..........................................................................................................................................H-153
4.3.59 SOFT SWITCH (软开关):#59 ..........................................................................................................................................H-153
4.3.60 SOFT SWITCH (软开关):#60 ..........................................................................................................................................H-154
4.3.61 SOFT SWITCH (软开关):#61 ..........................................................................................................................................H-155
4.3.62 SOFT SWITCH (软开关):#62 ..........................................................................................................................................H-155
4.3.63 SOFT SWITCH (软开关):#63 ..........................................................................................................................................H-155
4.3.64 SOFT SWITCH (软开关):#64 ..........................................................................................................................................H-156
5. 传真协议........................................................................................................................................................................................ H-157
5.1 G3 ECM (G3 错误修正模式)........................................................................................................................................... H-157
xii
5.2 线路控制 ............................................................................................................................................................................. H-158
5.2.1 G3 模式通讯步骤.....................................................................................................................................................................H-158
5.3 参考代码表.......................................................................................................................................................................... H-158
5.4 如何分析 T30 协议监视器 ................................................................................................................................................... H-159
I 固件 ..................................................................................................................................... I-1
1. 固件重写..............................................................................................................................................................................................I-1
1.1 概述........................................................................................................................................................................................... I-1
1.2 准备........................................................................................................................................................................................... I-1
1.3 重写方式 ................................................................................................................................................................................... I-1
2. 升级固件失败时的步骤........................................................................................................................................................................ I-3
J 故障排除 ............................................................................................................................. J-1
1. 卡纸画面............................................................................................................................................................................................. J-1
1.1 卡纸画面 .................................................................................................................................................................................. J-1
1.1.1 卡纸画面........................................................................................................................................................................................ J-1
1.1.2 显示重置步骤................................................................................................................................................................................ J-1
1.2 传感器布局............................................................................................................................................................................... J-2
1.2.1 主机 + PF-507 + AD-509 + DF-633 ............................................................................................................................................. J-2
1.3 解决方案 .................................................................................................................................................................................. J-2
1.3.1 初始检查项目................................................................................................................................................................................ J-2
1.3.2 纸盒 1 进纸部分卡纸.................................................................................................................................................................... J-3
1.3.3 手送纸盒进纸部分卡纸................................................................................................................................................................ J-3
1.3.4 纸盒 2 进纸部分卡纸.................................................................................................................................................................... J-4
1.3.5 图像转印部分卡纸........................................................................................................................................................................ J-5
1.3.6 定影部分卡纸................................................................................................................................................................................ J-5
1.3.7 双面进纸部分卡纸........................................................................................................................................................................ J-6
1.3.8 双面传送部分卡纸........................................................................................................................................................................ J-7
1.3.9 纸盒 3 进纸部分卡纸.................................................................................................................................................................... J-7
1.3.10 纸盒 3 传送部分卡纸.................................................................................................................................................................... J-8
1.3.11 纸盒 4 进纸部分卡纸.................................................................................................................................................................... J-9
1.3.12 纸盒 4 传送部分卡纸.................................................................................................................................................................... J-9
1.3.13 纸盒 5 进纸部分卡纸.................................................................................................................................................................. J-10
1.3.14 纸盒 5 传送部分卡纸.................................................................................................................................................................. J-10
1.3.15 进纸部分卡纸.............................................................................................................................................................................. J-11
1.3.16 传送部分卡纸.............................................................................................................................................................................. J-12
1.3.17 出纸部分卡纸.............................................................................................................................................................................. J-12
2. 故障代码........................................................................................................................................................................................... J-14
2.1 故障代码 (维修呼叫)........................................................................................................................................................... J-14
2.2 故障代码列表 ......................................................................................................................................................................... J-14
2.3 故障重置步骤 ......................................................................................................................................................................... J-14
2.4 解决方案 ................................................................................................................................................................................ J-15
2.4.1 C0211 ........................................................................................................................................................................................... J-15
2.4.2 C133C .......................................................................................................................................................................................... J-15
2.4.3 C2351........................................................................................................................................................................................... J-16
2.4.4 C2557、 C2558、 C255C........................................................................................................................................................... J-16
2.4.5 C2702........................................................................................................................................................................................... J-16
2.4.6 C3451、 C3751、 C3851............................................................................................................................................................ J-16
2.4.7 C3452、 C3752、 C3852............................................................................................................................................................ J-17
2.4.8 C4001、 C4101 ........................................................................................................................................................................... J-17
2.4.9 C5102........................................................................................................................................................................................... J-18
2.4.10 C5351........................................................................................................................................................................................... J-18
2.4.11 C6101........................................................................................................................................................................................... J-18
2.4.12 C9401........................................................................................................................................................................................... J-18
2.4.13 CC151、 CC153.......................................................................................................................................................................... J-19
xiii
2.4.14 CC163 .......................................................................................................................................................................................... J-19
2.4.15 CD301 .......................................................................................................................................................................................... J-19
2.4.16 CS001........................................................................................................................................................................................... J-19
3. 其它故障........................................................................................................................................................................................... J-20
3.1 机器打不开............................................................................................................................................................................. J-20
3.2 控制面板的不稳定操作 (和 MK-750 安装在一起)............................................................................................................... J-20
4. 图像质量问题 ................................................................................................................................................................................... J-21
4.1 故障排除步骤概述.................................................................................................................................................................. J-21
4.1.1 测试样张打印.............................................................................................................................................................................. J-21
4.2 修正措施步骤 ......................................................................................................................................................................... J-21
4.2.1 图像故障示例.............................................................................................................................................................................. J-21
4.2.2 白线,白色条纹.......................................................................................................................................................................... J-21
4.2.3 黑线,黑色条纹.......................................................................................................................................................................... J-22
4.2.4 浓度不均...................................................................................................................................................................................... J-23
4.2.5 图像浓度低.................................................................................................................................................................................. J-24
4.2.6 灰阶再现失败.............................................................................................................................................................................. J-25
4.2.7 背景模糊或图像粗糙.................................................................................................................................................................. J-26
4.2.8 空白区域...................................................................................................................................................................................... J-27
4.2.9 黑点.............................................................................................................................................................................................. J-27
4.2.10 折角.............................................................................................................................................................................................. J-28
4.2.11 空白复印...................................................................................................................................................................................... J-28
4.2.12 全黑复印...................................................................................................................................................................................... J-29
4.2.13 间距不均...................................................................................................................................................................................... J-30
4.2.14 波纹.............................................................................................................................................................................................. J-31
5. 传真故障........................................................................................................................................................................................... J-32
5.1 当传真的传输不正确时........................................................................................................................................................... J-32
5.1.1 无法发送传真.............................................................................................................................................................................. J-32
5.1.2 无法接收传真.............................................................................................................................................................................. J-33
5.1.3 拨号连接问题.............................................................................................................................................................................. J-34
5.2 通讯错误 ................................................................................................................................................................................ J-34
5.2.1 概述.............................................................................................................................................................................................. J-34
5.2.2 在传输期间发生错误.................................................................................................................................................................. J-35
5.2.3 在接收期间发生错误.................................................................................................................................................................. J-35
5.3 错误代码列表 ......................................................................................................................................................................... J-35
5.3.1 接收.............................................................................................................................................................................................. J-35
5.3.2 发送.............................................................................................................................................................................................. J-36
5.4 错误代码和相应解决方案 ....................................................................................................................................................... J-38
5.4.1 接收错误代码 (000X)............................................................................................................................................................. J-38
5.4.2 接收错误代码 (001X)............................................................................................................................................................. J-39
5.4.3 接收错误代码 (002X)............................................................................................................................................................. J-40
5.4.4 接收错误代码 (003X)............................................................................................................................................................. J-40
5.4.5 接收错误代码 (004X)............................................................................................................................................................. J-41
5.4.6 接收错误代码 (005X)............................................................................................................................................................. J-42
5.4.7 接收错误代码 (006X)............................................................................................................................................................. J-44
5.4.8 接收错误代码 (007X)............................................................................................................................................................. J-44
5.4.9 传输错误代码 (008X)............................................................................................................................................................. J-45
5.4.10 传输错误代码 (009X)............................................................................................................................................................. J-46
5.4.11 传输错误代码 (00AX)............................................................................................................................................................ J-47
5.4.12 传输错误代码 (00BX)............................................................................................................................................................ J-48
5.4.13 传输错误代码 (00CX)............................................................................................................................................................ J-49
5.4.14 传输错误代码 (00DX)............................................................................................................................................................ J-51
5.4.15 传输错误代码 (00EX)............................................................................................................................................................ J-52
5.4.16 传输错误代码 (00FX)............................................................................................................................................................ J-54
5.5 可以发送传真但无法接收传真................................................................................................................................................ J-56
5.6 传真线路提示正在通话........................................................................................................................................................... J-56
xiv
5.7 拿起电话听筒后机器未进入摘机状态 ..................................................................................................................................... J-57
5.8 在 VoIP 系统环境中,机器无法正确地传输传真 .................................................................................................................... J-57
6. 网络错误代码 ................................................................................................................................................................................... J-58
6.1 网络错误代码列表.................................................................................................................................................................. J-58
7. IC 保护装置...................................................................................................................................................................................... J-59
7.1 概述........................................................................................................................................................................................ J-59
7.2 IC 保护装置列表..................................................................................................................................................................... J-59
7.2.1 MFP 板......................................................................................................................................................................................... J-59
K 零件 / 连接头布局图 ...........................................................................................................K-1
1. 零件布局图.........................................................................................................................................................................................K-1
1.1 bizhub 225i/215i/205i...............................................................................................................................................................K-1
1.2 自动双面输稿器 (DF-633)....................................................................................................................................................K-2
1.3 PF-507.....................................................................................................................................................................................K-3
1.4 AD-509.....................................................................................................................................................................................K-3
2. 连接头布局图 .....................................................................................................................................................................................K-4
2.1 电路板接口布局图....................................................................................................................................................................K-4
2.1.1 bizhub 225i/215i/205i ...................................................................................................................................................................K-4
2.1.2 自动双面输稿器 (DF-633)......................................................................................................................................................K-6
2.1.3 PF-507...........................................................................................................................................................................................K-6
2.1.4 AD-509 .........................................................................................................................................................................................K-7
2.1.5 FK-510 ..........................................................................................................................................................................................K-7
2.1.6 MK-750.........................................................................................................................................................................................K-7
2.2 继电器连接头布局图 ................................................................................................................................................................K-8
2.2.1 bizhub 225i/215i/205i ...................................................................................................................................................................K-8
L 时序图 ................................................................................................................................ L-1
1. bizhub 225i/215i/205i.........................................................................................................................................................................L-1
2. DF-633...............................................................................................................................................................................................L-2
M 配线图 ............................................................................................................................... M-1
1. bizhub 225i/215i/205i........................................................................................................................................................................M-1
2. DF-633..............................................................................................................................................................................................M-2
3. PF-507 ..............................................................................................................................................................................................M-3
N 操作原理 ............................................................................................................................ N-1
1. bizhub 225i/215i/205i........................................................................................................................................................................ N-1
1.1 接口部分 ................................................................................................................................................................................. N-1
1.2 扫描器部分.............................................................................................................................................................................. N-1
1.2.1 配置...............................................................................................................................................................................................N-1
1.2.2 驱动...............................................................................................................................................................................................N-2
1.2.3 CIS 模块 .......................................................................................................................................................................................N-2
1.2.4 按 Start (开始)键时的控制.....................................................................................................................................................N-2
1.2.5 原稿尺寸检测机构.......................................................................................................................................................................N-3
1.3 写入部分 ................................................................................................................................................................................. N-4
1.3.1 配置...............................................................................................................................................................................................N-4
1.3.2 概述...............................................................................................................................................................................................N-4
1.3.3 激光发射区域...............................................................................................................................................................................N-5
1.4 碳粉供应部分 .......................................................................................................................................................................... N-5
1.4.1 配置...............................................................................................................................................................................................N-5
1.4.2 碳粉补充机构...............................................................................................................................................................................N-5
1.4.3 碳粉补充控制...............................................................................................................................................................................N-6
1.4.4 TC 恢复模式 ................................................................................................................................................................................N-6
1.4.5 碳粉用尽检测控制.......................................................................................................................................................................N-7
1.5 成像单元部分 .......................................................................................................................................................................... N-7
xv
1.5.1 配置...............................................................................................................................................................................................N-7
1.5.2 驱动...............................................................................................................................................................................................N-8
1.5.3 感光鼓驱动...................................................................................................................................................................................N-8
1.5.4 感光鼓充电...................................................................................................................................................................................N-8
1.5.5 碳粉流动.......................................................................................................................................................................................N-9
1.5.6 TCR 传感器自动调整..................................................................................................................................................................N-9
1.5.7 碳粉收集通道.............................................................................................................................................................................N-10
1.5.8 感光鼓向后旋转控制.................................................................................................................................................................N-10
1.5.9 显影偏压.....................................................................................................................................................................................N-10
1.5.10 成像单元寿命检测.....................................................................................................................................................................N-11
1.6 转印/分离部分..................................................................................................................................................................... N-11
1.6.1 配置.............................................................................................................................................................................................N-11
1.6.2 驱动.............................................................................................................................................................................................N-11
1.6.3 转印电压输出控制.....................................................................................................................................................................N-12
1.6.4 转印辊清洁控制.........................................................................................................................................................................N-12
1.6.5 纸张分离控制.............................................................................................................................................................................N-12
1.7 进纸部分 (纸盒 1).............................................................................................................................................................. N-13
1.7.1 配置.............................................................................................................................................................................................N-13
1.7.2 驱动.............................................................................................................................................................................................N-13
1.7.3 纸张提升板机构.........................................................................................................................................................................N-14
1.7.4 进纸控制.....................................................................................................................................................................................N-14
1.7.5 纸张尺寸检测机构.....................................................................................................................................................................N-15
1.7.6 缺纸检测控制.............................................................................................................................................................................N-16
1.7.7 纸盒开 / 关检测控制 .................................................................................................................................................................N-16
1.8 手送进纸部分 ........................................................................................................................................................................ N-17
1.8.1 配置.............................................................................................................................................................................................N-17
1.8.2 驱动.............................................................................................................................................................................................N-17
1.8.3 升/降控制.................................................................................................................................................................................N-17
1.8.4 进纸控制.....................................................................................................................................................................................N-18
1.8.5 缺纸检测控制.............................................................................................................................................................................N-19
1.9 对位部分 ............................................................................................................................................................................... N-19
1.9.1 配置.............................................................................................................................................................................................N-19
1.9.2 驱动.............................................................................................................................................................................................N-20
1.9.3 对位控制.....................................................................................................................................................................................N-20
1.10 定影部分 ............................................................................................................................................................................... N-21
1.10.1 配置.............................................................................................................................................................................................N-21
1.10.2 定影驱动控制.............................................................................................................................................................................N-21
1.10.3 定影压力控制.............................................................................................................................................................................N-21
1.10.4 定影温度控制.............................................................................................................................................................................N-22
1.10.5 异常高温保护.............................................................................................................................................................................N-23
1.10.6 PPM 控制....................................................................................................................................................................................N-23
1.10.7 新物品检测.................................................................................................................................................................................N-23
1.11 出纸部分 ............................................................................................................................................................................... N-23
1.11.1 配置.............................................................................................................................................................................................N-23
1.11.2 传输控制.....................................................................................................................................................................................N-24
1.12 图像稳定控制 ........................................................................................................................................................................ N-24
1.12.1 配置.............................................................................................................................................................................................N-24
1.13 电源部分 ............................................................................................................................................................................... N-25
1.13.1 配置.............................................................................................................................................................................................N-25
1.13.2 操作.............................................................................................................................................................................................N-25
1.14 风扇控制 ............................................................................................................................................................................... N-25
1.14.1 配置.............................................................................................................................................................................................N-25
1.14.2 功能.............................................................................................................................................................................................N-25
1.14.3 风扇控制.....................................................................................................................................................................................N-26
2. DF-633............................................................................................................................................................................................ N-27
xvi
2.1 配置....................................................................................................................................................................................... N-27
2.1.1 各部分配置.................................................................................................................................................................................N-27
2.1.2 主体部分配置.............................................................................................................................................................................N-27
2.2 概述....................................................................................................................................................................................... N-28
2.2.1 纸张通道.....................................................................................................................................................................................N-28
2.2.2 纸张通道操作.............................................................................................................................................................................N-28
2.3 进纸部分 ............................................................................................................................................................................... N-30
2.3.1 进纸驱动.....................................................................................................................................................................................N-30
2.3.2 文件放置/缺纸检测.................................................................................................................................................................N-30
2.3.3 文件尺寸检测机构.....................................................................................................................................................................N-31
2.3.4 文件尺寸检测表.........................................................................................................................................................................N-32
2.3.5 混合原稿检测.............................................................................................................................................................................N-32
2.3.6 拾纸辊升/降控制.....................................................................................................................................................................N-33
2.3.7 进纸 / 分离控制 .........................................................................................................................................................................N-33
2.4 对位部分 ............................................................................................................................................................................... N-34
2.4.1 对位驱动.....................................................................................................................................................................................N-34
2.4.2 波幅形成过程.............................................................................................................................................................................N-35
2.5 文档读取部分 ........................................................................................................................................................................ N-35
2.5.1 文档读取驱动.............................................................................................................................................................................N-35
2.5.2 传送机构.....................................................................................................................................................................................N-36
2.6 反转 / 出纸部分 ..................................................................................................................................................................... N-36
2.6.1 反转 / 出纸驱动 .........................................................................................................................................................................N-36
2.6.2 反转 / 出纸的切换机构 .............................................................................................................................................................N-37
3. PF-507 ............................................................................................................................................................................................ N-38
3.1 配置 / 驱动............................................................................................................................................................................. N-38
3.2 操作....................................................................................................................................................................................... N-38
3.2.1 进纸纸盒就位检测.....................................................................................................................................................................N-38
3.2.2 纸张提升板.................................................................................................................................................................................N-39
3.2.3 纸张尺寸检测机构.....................................................................................................................................................................N-40
3.2.4 纸张分离机构.............................................................................................................................................................................N-41
4. AD-509............................................................................................................................................................................................ N-42
4.1 配置 / 驱动............................................................................................................................................................................. N-42
4.2 操作....................................................................................................................................................................................... N-42
4.2.1 纸张传送控制.............................................................................................................................................................................N-42
4.2.2 双面器单元中的纸张传输控制.................................................................................................................................................N-43
暂无购物记录
    暂无商品评价
服务时间 9:00-22:00